home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Packard Bell - Multimedia…D & Packard Bell Library
/
Packard Bell Master CD.iso
/
diskimag
/
pnp
/
disk1.img
/
DB
/
DPTBC01.CF_
/
DPTBC01.bin
Wrap
Text File
|
1995-02-09
|
11KB
|
357 lines
;
; (C)Copyright Distributed Processing Technology, 1990-1991
; All Rights Reserved.
;
; DPT PM3011/75 ESDI Caching Hard/Floppy Disk Controller Configuration File
;
; Date = 1/22/91
; Version = (See version at end of this file.)
; Filename = !DPTBC01.CFG
;
BOARD
ID = "DPTBC01"
NAME = "DPT ESDI Caching Hard Disk Controller (PM3011/7X)"
MFR = "DPT"
CATEGORY = "MSD"
SLOT = ISA16
LENGTH = 341
AMPERAGE = 3400
SKIRT = NO
READID = NO
IOCHECK = INVALID
DISABLE = UNSUPPORTED
COMMENTS = "\nThe Distributed Processing Technology PM3011/7X is a high
performance ESDI Caching Hard Disk Controller with an 16-bit AT
interface.\n
Key features of the adapter are:\n\n
\t* Emulates a WD1003-WA2 MFM controller\n
\t* Requires NO drivers for all standard PC-AT OS's\n
\t* 0.5ms access on a Cache hit\n
\t* Supports 5, 10, 15, and 20 MHz ESDI drives\n
\t* PIO transfer rate up to 4 MB/sec\n
\t* Supports up to 16 MB of cache memory\n
\t* Optional Hardware Disk Mirroring for all OS's"
HELP = "For additional information, contact:\n\n
\tDistributed Processing Technology\n
\t140 Candace Drive\n
\tMaitland, Florida 32751\n
\t(407) 830-5522 Voice\n
\t(407) 260-5366 Fax\n
\t(407) 831-6432 BBS"
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
JUMPER(1) = 1
NAME = "Hard Disk I/O"
JTYPE = PAIRED
LABEL = LOC(1) "Y17"
FACTORY = LOC(1) 0
COMMENTS = "Install jumper for Secondary address."
HELP = "The Primary address should be chosen for booting an OS with
a standard AT BIOS."
JUMPER(2) = 3
NAME = "Hard Interrupt Level"
JTYPE = PAIRED
LABEL = LOC(1 2 3) "Y8" "Y9" "Y10"
REVERSE = YES
FACTORY = LOC(1 2 3) 100
COMMENTS = "Install jumper to select Interrupt level."
HELP = "Interrupt 14 should be chosen for booting an OS with
a standard AT BIOS."
JUMPER(3) = 1
NAME = "Floppy Disable"
JTYPE = PAIRED
LABEL = LOC(1) "Y20"
FACTORY = LOC(1) 0
COMMENTS = "Install jumper to disable floppy."
HELP = "When used with AT's with motherboard floppies, the PM3011
floppy should be disabled."
JUMPER(4) = 1
NAME = "Floppy I/O"
JTYPE = PAIRED
LABEL = LOC(1) "Y5"
FACTORY = LOC(1) 0
COMMENTS = "Install jumper for Secondary address."
HELP = "The Primary address should be chosen for accessing the floppy
with a standard floppy driver."
JUMPER(5) = 1
NAME = "Floppy Head Load"
JTYPE = PAIRED
LABEL = LOC(1) "Y21"
FACTORY = LOC(1) 0
COMMENTS = "Install jumper to use PM3011 with older PC floppy drives."
HELP = "This jumper is never typically installed."
JUMPER(6) = 1
NAME = "Option ROM Enable"
JTYPE = PAIRED
LABEL = LOC(1) "Y7"
FACTORY = LOC(1) 0
COMMENTS = "Install jumper to enable Option ROM."
HELP = "The Option ROM Enable jumper is shipped from the factory
installed, allowing ROM address decoding. This ROM is
normally the BR401X SmartROM, an INT13 replacement BIOS."
JUMPER(7) = 1
NAME = "Option ROM Address"
JTYPE = PAIRED
LABEL = LOC(1) "Y18"
FACTORY = LOC(1) 0
COMMENTS = "Install jumper for alternate address."
HELP = "The Option ROM Address jumper is shipped from the
factory removed, allowing the ROM to be decoded at address
C8000h. Installed, the ROM is decoded at D8000h."
JUMPER(8) = 1
NAME = "SCSI Port Enable"
JTYPE = PAIRED
LABEL = LOC(1) "Y6"
FACTORY = LOC(1) 0
COMMENTS = "Install jumper to enable optional SCSI port."
HELP = "This optional is available on PM3011's with the model suffix
/xx9."
JUMPER(9) = 1
NAME = "SCSI Port Address"
JTYPE = PAIRED
LABEL = LOC(1) "Y19"
FACTORY = LOC(1) 0
COMMENTS = "Install jumper for alternate address."
HELP = "Two addresses are allowed to prevent system conflicts."
JUMPER(10) = 2
NAME = "SCSI Interrupt Level"
JTYPE = PAIRED
LABEL = LOC(1 2) "Y11" "Y12"
REVERSE = YES
FACTORY = LOC(1 2) 00
COMMENTS = "Install jumper to select interrupt level."
JUMPER(11) = 4
NAME = "SCSI DMA Channel"
JTYPE = PAIRED
LABEL = LOC(1 2 3 4) "Y13" "Y14" "Y15" "Y16"
REVERSE = YES
FACTORY = LOC(1 2 3 4) 0000
COMMENTS = "Install jumper for DMA channel."
HELP = "The DMA channel on the motherboard may be used to transfer
data."
JUMPER(12) = 2
NAME = "Not Used"
JTYPE = PAIRED
LABEL = LOC(1 2) "Y1" "Y2"
REVERSE = YES
FACTORY = LOC(1 2) 00
COMMENTS = "Not used - Do not jumper!"
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
FUNCTION = "Hard Drive"
TYPE = "MSD,DSKCTL"
SUBFUNCTION = "I/O Ports"
COMMENTS = "Select Primary to boot in WD1003 mode."
CONNECTION = "Control Cable Connector, J5\n
Drive 0 Data Cable Connector, J4\n
Drive 1 Data Cable Connector, J3\n
Drive 2 Data Cable Connector, J2\n
Drive 3 Data Cable Connector, J1"
CHOICE = "Primary (Bootable)"
FREE
PORT = 1F0h
SIZE = WORD
PORT = 1F1h-1F7h
INIT = JUMPER(1) LOC(1) 0
CHOICE = "Secondary"
FREE
PORT = 170h
SIZE = WORD
PORT = 171h-177h
INIT = JUMPER(1) LOC(1) 1
SUBFUNCTION = "Interrupt Number"
COMMENTS = "Select 14 to boot in WD1003 mode."
CHOICE = "14 (Bootable)"
FREE
IRQ = 14
TRIGGER = EDGE
INIT = JUMPER(2) LOC(1 2 3) 100
CHOICE = "12"
FREE
IRQ = 12
TRIGGER = EDGE
INIT = JUMPER(2) LOC(1 2 3) 001
CHOICE = "7"
FREE
IRQ = 7
TRIGGER = EDGE
INIT = JUMPER(2) LOC(1 2 3) 010
CHOICE = "Disabled"
DISABLE = YES
FREE
INIT = JUMPER(2) LOC(1 2 3) 000
SUBFUNCTION = "Option ROM Address"
COMMENTS = "Select BIOS address, if enabled."
CHOICE = "Enabled @ C8000h"
FREE
INIT = JUMPER(7) LOC(1) 0
INIT = JUMPER(6) LOC(1) 1
MEMORY = 8K
ADDRESS = 0C8000h
WRITABLE = NO
MEMTYPE = OTH
SIZE = BYTE
CACHE = YES
CHOICE = "Disabled"
DISABLE = YES
FREE
INIT = JUMPER(6) LOC(1) 0
CHOICE = "Enabled @ D8000h"
FREE
INIT = JUMPER(7) LOC(1) 1
INIT = JUMPER(6) LOC(1) 1
MEMORY = 8K
ADDRESS = 0D8000h
WRITABLE = NO
MEMTYPE = OTH
SIZE = BYTE
CACHE = YES
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
FUNCTION = "Floppy Drive"
TYPE = "FDC,FPYCTL"
SUBFUNCTION = "I/O Ports"
COMMENTS = "Select Primary to access floppy with standard driver."
CONNECTION = "Floppy Cable, J8"
CHOICE = "Primary"
FREE
PORT = 3F0h-3F7h
INIT = JUMPER(3) LOC(1) 0
INIT = JUMPER(4) LOC(1) 0
CHOICE = "Secondary"
FREE
PORT = 370h-377h
INIT = JUMPER(3) LOC(1) 0
INIT = JUMPER(4) LOC(1) 1
CHOICE = "Disabled"
DISABLE = YES
FREE
INIT = JUMPER(3) LOC(1) 1
SUBFUNCTION = "Head Load"
COMMENTS = "Select Enable only for older PC floppy drives."
CHOICE = "Disabled"
FREE
INIT = JUMPER(5) LOC(1) 0
CHOICE = "Enabled"
FREE
INIT = JUMPER(5) LOC(1) 1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; moved option ROM group to HardDrive subfunction
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
FUNCTION = "SCSI Port"
TYPE = "SCS"
SUBFUNCTION = "I/O Ports"
COMMENTS = "Select SCSI address, if enabled."
CONNECTION = "Internal SCSI Connector, J10\n
External SCSI Connector, J11"
CHOICE = "Disabled"
DISABLE = YES
FREE
INIT = JUMPER(8) LOC(1) 0
CHOICE = "Enabled @ CB000h"
FREE
INIT = JUMPER(9) LOC(1) 0
INIT = JUMPER(8) LOC(1) 1
MEMORY = 1K
ADDRESS = 0CB000h
WRITABLE = YES
MEMTYPE = OTH
SIZE = BYTE
CACHE = NO
CHOICE = "Enabled @ DB000h"
FREE
INIT = JUMPER(9) LOC(1) 1
INIT = JUMPER(8) LOC(1) 1
MEMORY = 1K
ADDRESS = 0DB000h
WRITABLE = YES
MEMTYPE = OTH
SIZE = BYTE
CACHE = NO
SUBFUNCTION = "Interrupt Number"
COMMENTS = "Select SCSI interrupt level."
CHOICE = "Disabled"
DISABLE = YES
FREE
INIT = JUMPER(10) LOC(1 2) 00
CHOICE = "12"
FREE
IRQ = 12
TRIGGER = EDGE
INIT = JUMPER(10) LOC(1 2) 10
CHOICE = "7"
FREE
IRQ = 7
TRIGGER = EDGE
INIT = JUMPER(10) LOC(1 2) 01
SUBFUNCTION = "DMA Channel"
COMMENTS = "Select SCSI DMA channel."
CHOICE = "Disabled"
DISABLE = YES
FREE
INIT = JUMPER(11) LOC(1 2 3 4) 0000
CHOICE = "1"
FREE
DMA = 1
SIZE = BYTE
INIT = JUMPER(11) LOC(1 2 3 4) 1010
CHOICE = "3"
FREE
DMA = 3
SIZE = BYTE
INIT = JUMPER(11) LOC(1 2 3 4) 0101
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
FUNCTION = "Memory Expansion"
SHOW = NO
TYPE = "MEM"
COMMENTS = "Additional cache memory may be attached to these connectors."
CONNECTION = "Memory Expansion Connector, J9\n
Memory Module Connectors, J7/J12"
CHOICE = "none"
FUNCTION = "Front Panel Hard Disk Activity LED"
SHOW = NO
TYPE = "OTH"
COMMENTS = "Additional cache memory may be attached to these connectors."
CONNECTION = "Controller Busy Connector, J6"
CHOICE = "none"
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
FUNCTION = "!DPTBC01.CFG Version"
CHOICE = "003A"
FREE
INIT = JUMPER(11) LOC(1 2) 00